Fabral is the premier supplier of metal roofing and wall panels for architectural, educational, commercial, industrial and agricultural applications.
With a concealed fastener, this plush panel design is suited for long spanning walls, equipment screens, fascia and soffit applications. Panels have also been utilized as a rainscreen system
For long spanning walls, this panel does not require clips. It is “six up six down” and for vertical use. Functionality is key with this standard panel
Décor Flush II panels are recommended for siding, fascias, or soffits only. When used for wall applications, Décor Flush II should only be installed vertically. Install panels plumb, level and straight so it is watertight and without waves or other distortions, allowing for thermal movement considerations. Apply sealant tape or caulking as necessary at flashing and panel joints to prevent water penetration.
This attractive concealed fastener system is ideal for soffit, fascia and vertical wall applications
This panel system is ideal for soffit applications
This high performance, mechanically seamed roof system satisfies the most demanding applications. The panels can be roll-formed and curved to span an entire roof without end seams.
| Wind Uplift | UL90 | #275, 275A, 275B |
|---|---|---|
| ASTM E330 | 24 ga. allowable load of 95.76 psf @ 2.5′ | |
| 22 ga. allowable load of 87.88 psf @ 5′ | ||
| .032″ AL allowable load of 48.48 psf @ 5′ | ||
| .032″ AL allowable load of 66.67 psf @ 2.5′ | ||
| .040″ AL allowable load of 66.67 psf @ 5′ | ||
| .040″ AL allowable load of 82.42 psf @ 2.5′ | ||
| Air infiltration | ASTM E283 | .006 @ 20 psf |
| ASTM E1680 | 0.00 @ 20 psf | |
| ASTM E331 | no water @ 20 psf | |
| ASTM E1646 | no water @ 20 psf |
When curving is required for a design, this mechanically seamed structural standing seam roof panel can bend to create the desired look
| Wind uplift | UL90 | #90, 176, 180, 238, 548, 549 |
| Air infiltration | ASTM E283ASTM E1680 | .01 @ 15 psfLess than .01 @ 1.57psf |
| Water penetration | ASTM E331ASTM E1646ASTM E2140 | No water @ 6.24 psfNo water @ 16 psfNo water at 6 hours |
| Substrate | Width | 3.0’ | 3.5’ | 4.0’ | 4.5’ | 5.0’ |
|---|---|---|---|---|---|---|
| 24 g steel | 12” | 53 | 53 | 53 | 53 | 53 |
| 24 g steel | 18” | 35 | 35 | 35 | 35 | 35 |
| 22 g steel | 12” | 70 | 70 | 70 | 70 | 70 |
| 22 g steel | 18” | 47 | 47 | 47 | 47 | 47 |
With superior strength and spanning capability, Fabral Powerseam II is a high-performance, mechanically seamed standing seam roofing system. With 180 degree machine seaming, field rollforming and the ability to curve to a minimum 10’ radius, Powerseam II delivers performance and value to education, athletic and industrial projects. Shadow lines and stiffening ribs available
| Air Infiltration | ASTM E283 | 0.01 cfm/ft2 @ 15 psf |
| ASTM E1680 | <0.01 cfm/ft2 @ 1.57 psf | |
| Water Penetration | ASTM E331 | No water leakage @ 6.24 psf |
| ASTM E1646 | No water leakage @ 2.86 psf | |
| ASTM E2140 | No leakage of standing water | |
| Wind Uplift | ASTM E1592 | Test results vary depending on gauge and panel thickness |
| UL580 | Class 90 |
| Substrate | Width | Spans | 2′-0″ | 2′-6″ | 3′-0″ | 3′-6″ | 4′-0″ | 4′-6″ | 5′-0″ |
|---|---|---|---|---|---|---|---|---|---|
| 24 ga. Steel | 16” | 3+ | 102 | 92 | 82 | 73 | 63 | 53 | 44 |
A snap-together panel for easy installation with no mechanical seaming tool required. Ideal for installation over solid substrate and open framing.
| Wind Uplift | UL580 | Class 90 #303, 359, 359A, 343, 417 |
| ASTM E1592 | Results Vary Depending on Gauge and Panel Thicknessa | |
| Air infiltration | ASTM E283 | .009 @ 6.24 psf |
| Water penetration | ASTM E331 | no water @ 15 psf |
Economical high performance standing seam peak system. Panel is ideal for installing over solid substrate and open framing.
SLIM SEAM IMPROVEMENTS 2018: Slim Seam Florida Approval
| Wind uplift | UL90 | #274, 274A, 369 |
|---|---|---|
| ASTM E1592 | 24 ga. allowable load of 48.48 psf @ 2.5’ | |
| Air infiltration | ASTM E283 | 0.09 cfm/ft2 @ 1.57 psf |
| ASTM E1680 | 0.00 @ 20 psf | |
| Water penetration | ASTM E331 | no water @ 25 psf |
| ASTM E1646 | no water @ 12 psf |
For a classic panel with narrow batten seams, this is available in a variety of gauges and has taper options
| Wind uplift | UL90 | #190, 190B |
|---|---|---|
| Air infiltration | ASTM E283 | No air penetraion @ 20 psf |
| ASTM E1680 | 0.019 cfm/ft2 @ 20 psf | |
| Water penetration | ASTM E331 | No Water @ 20 psf |
| ASTM E1546 | No water @ 20 psf |
This two-component design is ideal for roof applications requiring curved panels. It is durable and allows for creativity in design
Modern-day models for education facilities have been designed with Fabral products. As the leading provider of metal for building envelope solutions, Fabral systems have been specified for projects in every commercial building segment. Durable exterior cladding is fitting for schools to tightly seal the building — netting next-level energy efficiency.
Use this Spec Builder to create custom packages or download a complete Submittal Package for the Fabral Stand N Seam, PowerSeam, Thin Seam, Hefti-Rib, or HCF panels.
Click below for pre-packackged zipped downloads.
To download files for additional Fabral panels and build your own specification package, name your file and then begin selecting.